FAMPARC
4:1 balun
updated 29 sep. 2024
new stock! as of October 2024
The Famparc club is now selling the Famparc 4:1 Balun for use with an Off Centre Fed Antenna. (OCF)
​
Richard VK3TXD has done a massive amount or work including testing for the best efficiency and performance.
​
Built Using: (This is a fully built and ready to use)
​
-
3D printed sled for mounting toroids & cap
-
Toroid pack, 35mm OD pack of 2
-
Wings Nuts form connecting Each Arm
-
SO239 Socket
-
Wire twisted for 1:1, 0.80mm
-
Wire for 64:1, 0.80mm
-
Poly carbonate box
​
​
AVAILABLE FROM FAMPARC
​
$60.00
​
Can Freight Australia Wide for $20.00.​
​
Payment can be made via direct deposit at:
NAB, Frankston BSB: 083-253 Acct No: 03-683-3688
Note: Wire for radials Not Supplied.
For an 80-10 meter OCF dipole antenna, divide the 1⁄2 wavelength standard of 468 by the lowest operating frequency of 3.6 MHz and you arrive at an overall length of 39.624M (130′). This is the length of a standard dipole but instead of dividing the result in half, use a 36/64% offset to determine the feedpoint.
​
The total length of 39.624M (130′) multiplied by 0.64 (64%) gives the long leg length of 25.360M (83.2 feet). The short leg length is the remainder or 14.265M (46.8 feet).
​
Using a quality CURRENT 4:1 balun at the feed point is crucial to the overall performance of the antenna when they are fed with coaxial cables.
The feedpoint impedance at the offset is at or about 200 Ohms and the balun will provide good transformation to the coax feedline impedance of 50 Ohms.
RF Choke (Important)
​
The OCF 80M or 40M model, does use a portion of the feed line prior to the 4:1 Balun as a Radiator. This can produce RF on the feed line, thus causing all sorts of of RF issues in the shack and your transceiver. Therefor a RF Choke is very important. For the 80M OCF version the location of the choke is around 6.7M before the Balun. See Images.. Not suppled.
​
After installing the OCF, check the resonant frequency on or lowest SWR for 80 meters. It should be in the low portion of the 80 meter band (e.g., 3.5 MHz or lower).
Now you can begin trimming small lengths of wire off each end of the OCF to obtain the lowest SWR at 3.6 MHz.
Begin with no more than 6 inches in total with 4 inches removed from the long leg and 2 inches off the short leg. Be sure to trim each wire proportionately.
For example, if you cut 150mm off the long leg, cut only 75mm off the short leg. Depending on your surroundings and antenna height, 80m may only reach an SWR of 1.8 – 2.0:1. This is normal and the higher bands will be lower.
​
40M OCF (Off centre fed) antenna
The 40M Off Centre Fed Antenna (OCF), you can use the same guidelines and principles from the above 80M version.
​
Of course the physical size is smaller, being the dimensions are less then the 80M version.
​
So using the same text as above for the 80M version, simply use the dimensions listed in the graphic below.
​
The 40M version will work on 80M but a tuner is needed, and of course the efficiency is less, however the 40M version is reasonably compact as you can see by the long leg being 12.5M and 7.62M for the short.
You will also require the 4:1 Current Balun as like the 80M version.
​
Also, cut long and tune each leg for best SWR.
​
Now get out there, make one and have fun!
Note: For any antenna to be effective, it is recommend that it be at a reasonable height above the ground and away from other obstacles. The video above, although the antenna was very effective, was not used in a optimal configuration.
Warning: When using antenna within public areas or where people or animals may come in to contact with the antenna or feed lines.. Please be mindful and make sure that any wire or feed lines are placed so that they cannot injure people or animals and that all wires are made so that they are easily seen. Marking the wires is recommend.
Cash and Pickup preferred at the Club Rooms.. However we can offer shipping for an extra $20.00, and Direct Deposit can be accepted. Please make note of payment method when sending your email using the Button above.
Note: The above button well open your email client.
Please include what you are ordering along with your contact details.
Sorry Australia residents only.